It is currently Mon May 29, 2017 3:04 pm



Post new topic Reply to topic  [ 30 posts ]  Go to page Previous  1, 2
Author Message
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Sat May 07, 2011 11:44 pm 
Offline
Newbie
User avatar

Joined: Sun Apr 03, 2011 1:01 am
Posts: 19
Location: New mexico
Tomatolord

Sorry so long. Been out for a bit and didn't see your question. I didn't weld it because that isn't in my skill set. I installed a new one due to some stripping of the inside spooned. As fate would have it the EXACT same thing has now happened to the other side and I am following same course of action. I bought a new cv unit, installed it, got a new hub and am installing that. After discussion with Casey at Joyner he tells me that the wheel bearings have a plastic portion which tends to break apart. When this happens you get extra mvmt and the castle nut eventually backs off. This is evident in mine. The bearings were destroyed and plastic parts came out. The new ones I bought for both side are solid metal (not sure If steel or aluminum). They are much sturdier. Hope this prevents future issues.

Once again. Sorry I took so long. I just figured out how to have items sent right to my email to key me in when something comes in. Take care and ket me know what you decide to do..

Nardo


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Sun May 08, 2011 9:14 am 
Offline
Buggified
User avatar

Joined: Thu Mar 19, 2009 11:49 pm
Posts: 589
Images: 2
Location: Pelham, TN
What wheel bearings did you buy?
I want to change mine to some sealed style
How much and where?

_________________
Joyner 650 SS
Polaris Ranger 700 XP


Top
 Profile Personal album  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Wed May 11, 2011 6:15 pm 
Offline
Initiated

Joined: Tue Aug 31, 2010 4:26 pm
Posts: 82
Location: Land o Sand, Arizona
I'm interested too.

Casey is a good guy. Hes helped me with quite a few problems and gets me parts and isn't afraid to recommend someone else if he doesn't have the part.


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Tue Mar 27, 2012 7:51 pm 
Offline
Buggy Enthusiast

Joined: Wed Mar 30, 2011 9:32 pm
Posts: 131
Location: NorCal
I realize this is an old post, but thought I would refresh it because I need some help......

Busted the right axle near the castle nut...ooops. Talked to Casey great guy, extremely helpful, part on the UPs truck....all good.

Before I read all the details on how to properly remove the old axle I yanked out the old axle by slide hammering (very DIY slide hammer) on the OUTSIDE CV joint. Doing this popped the solid axle out of the inner CV joint (broke the snap ring that retains the axle)....so far not a problem since I'm replacing the whole thing.

The inner joint Bell housing is still on the trans output shaft. Go to Autozone, get the legit slide hammer and right angle axle puller thing. Start banging away on inner joint, will not come off. Check and double check that the right angle "fork" is only grabbing the CV housing when trying to slide hammer (there is another piece of something that is easy to catch just fwd of the CV housing). Arm hurts, hand bruised, axle still on....what the heck. Pop off the retaining ring holding the inner guts of the CV...guts come out, Bent snap ring come out (the one that used to be attached to the end of the axle). Now I can clearly see the internal side of the trans end of the inner CV housing.....doesn't appear to be anything to remove to "release it" from the trans output shaft....what the heck.

UPS truck arrived this afternoon with the new axle, but I still can't get the old inner CV housing off. Am I missing something? Anybody have have any idea?


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Tue Mar 27, 2012 7:52 pm 
Offline
Buggy Enthusiast

Joined: Wed Mar 30, 2011 9:32 pm
Posts: 131
Location: NorCal
sorry....2006 650 SS


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Sun Apr 01, 2012 11:09 pm 
Offline
Buggified
User avatar

Joined: Thu Mar 19, 2009 11:49 pm
Posts: 589
Images: 2
Location: Pelham, TN
Picture please.
Not sure if I understand what you have left in the transmission

_________________
Joyner 650 SS
Polaris Ranger 700 XP


Top
 Profile Personal album  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Mon Apr 02, 2012 11:59 am 
Offline
Buggy Enthusiast

Joined: Wed Mar 30, 2011 9:32 pm
Posts: 131
Location: NorCal
Crispin, thanks for the reply but I finally got it out. The "bell housing" for the inner CV joint was the only thing left still attached to the tranny output shaft. A little heat, some more slide hammering, and two pry bars finally convinced that part to get off. New axle is in. Now shifting to the other side to replace the CV boots....hopefully that one comes off easier.


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Fri Nov 11, 2016 4:29 pm 
Offline
Probie

Joined: Fri Nov 11, 2016 4:25 pm
Posts: 1
This is a really old thread and this is a long shot but I am wondering if artic cat outer CVS will work on my 650 joyner axle


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Fri Nov 18, 2016 7:57 am 
Offline
Probie

Joined: Fri Nov 18, 2016 7:50 am
Posts: 1
No Limits Powersports in Arlington Texas - Contact Jarrad (Snowman6479). (817)695-1151 http://www.joyner-atv-utv.com/
Silver Bullet Motorsports in Yuma Arizona - Contact (silverbullet). (928) 344-2117 http://www.silverbul...otorsports.net/
Thin Air Powersports in Spring Creek Nevada - Contacts Tim (Anylizer) or Amanda (Long Track Lady) (775)753-8223 http://www.thinairpowersports.com/
McCoy Motorsports in Pikeville Kentucky - Contact Art (Art) (606)432-1556 http://www.tobefast....sa-c-63727.html
Mudslingers Motorsports, Alberta, Canada, Trevor Carson (780) 576-2860 cell: (780) 984-2711 http://www.mudslinge...website_006.htm


I also take suggestions for any and everyone!!



parts & pieces from dealer in Germany
http://www.utvboard....-parts/?p=18349

AIR FILTER K&N RU-1000, RC-4160, and another link
If you have the new 09 filter box, w/ Fram # CA-7764
ALTERNATOR BELT 14mmx 755mm replacement that works....Carquest #K040292
Alternator Belt - Checkers Auto Parts KO40292 - Exact Match
Battery, according to 2 scoops, Duralast 51-DL is the correct size.
OIL FILTERS
Troopers with Thread Size 20X1.5 MM can use:
WIX 51347, 51334 --- Napa 1347, 1334, PS1334 --- Fram PH6010A, PH3593A
Troopers with Thread Size 3/4X16 " can use:
Fram PH4967, Napa 1394 & Wix 5194 (slightly longer than original, Wix 51396 (even longer yet).

_________________
we provide assignment help uk.


Top
 Profile  
 
 Post subject: Re: Need help to remove Joyner rear axle
PostPosted: Fri Nov 18, 2016 7:31 pm 
Offline
Sponsoring Dealer
Sponsoring Dealer
User avatar

Joined: Tue Jan 24, 2006 8:18 am
Posts: 19887
Images: 22
Location: Prattville, AL
I have tried the cv joint from a artic cat, it don't fit

_________________
American sportworks, Renli, Kymco, Landmaster , Hyosung,
Tucker Rocky Dealer
Parts Unlimited, Western Powersports,
http://www.mpsracing.net
www.mpsracing.net


Top
 Profile Personal album  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 30 posts ]  Go to page Previous  1, 2


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

blackLevel designed by GrafsS



phpBB SEO
© Buggynews.com - All Rights Reserved