Joined: Fri Jul 29, 2005 7:46 pm Posts: 538 Location: LI NY
can someone recomend some easy and maybe cheap mods. i dont know how hard it is to do a carb but I have no expirence with any on this. My father is into cars so he should be able to help but my neighbor knows just about everything. i just dont want to bother him for so long while i watch him install a carb for me.i would feel bad cause he has stuff to do
_________________ 2006 Blade 250XT: Eletric Dual Note Air Horns, Chrome UNI and 127.5 Jet, Upgraded Battery 20 Amp/Hrs
Joined: Thu May 05, 2005 5:17 am Posts: 3348 Location: Sunbury, Ohio
Bolt from devilville was the variator nutt.
The CVT cover usually requires you to take the muffiler off, or get it out of the way. Mine muffiler unbolts so I dont need to disconnect it from the engine.
Attachments:
Pipe Off.JPG [ 89.77 KiB | Viewed 3 times ]
_________________ 2004 Carter Brothers Talon-DLX150IIR
The best way to learn is to pull out the wrenches and start turning them. If you have any problems you know where to post a question. There are lots of people on here to help you conquer just about anything. The easiest and cheapest mod you can do to improve the performance of your buggy is change the rollers like Jabo said. I don't know much about the 250dx but I think it is the same motor as what is in the 250xt. So once more people start getting the 250xt's, the more people will be able to help you.If you don't have the tools, you better start saving your money or know someone with them. You are going to need a decent socket set(metric) and a decent set of open end wrenches. If you want to tear into the CVT and replace rollers, you will also need an impact wrench. Hopefully your neighbor can help you out there.
Good luck and keep us posted as to what projects you take on.
250dx wrote:
can someone recomend some easy and maybe cheap mods. i dont know how hard it is to do a carb but I have no expirence with any on this. My father is into cars so he should be able to help but my neighbor knows just about everything. i just dont want to bother him for so long while i watch him install a carb for me.i would feel bad cause he has stuff to do
Joined: Fri Jul 29, 2005 7:46 pm Posts: 538 Location: LI NY
i have a garage full of tools. from welders to a 300gal air tank and compressor suspended from the ceiling. i just dont know how to use them. my dad does though. I no longer have a 250dx. that was my old cart. I am getting an XT. Hopsterguy,if you see this please change my name to something else. 250XT or Way2Evil. thanks for your responses. Is there a write-up on the redneck mod?
_________________ 2006 Blade 250XT: Eletric Dual Note Air Horns, Chrome UNI and 127.5 Jet, Upgraded Battery 20 Amp/Hrs
If you want your name changed, pm Steve. He will change it for you.
250XT wrote:
i have a garage full of tools. from welders to a 300gal air tank and compressor suspended from the ceiling. i just dont know how to use them. my dad does though. I no longer have a 250dx. that was my old cart. I am getting an XT. Hopsterguy,if you see this please change my name to something else. 250XT or Way2Evil. thanks for your responses. Is there a write-up on the redneck mod?
Users browsing this forum: No registered users and 1 guest
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
I would suggest getting rollers first!!!!
